How to replace your Bubendorff roller shutter remote control ?
Have you lost or broken the remote control for your roller shutter? Each remote control has a “proprietary” protocol, very secure and unique. Don't panic, it is possible to replace it by reproducing a transmitter identical to the one supplied with your shutter.
Replacement remote control: installation procedure for a roller shutter connected to the electrical network (230V)
This procedure is quite basic. Proper compliance with the indicated timings is imperative to ensure success. You can equip yourself with a timer (available on your phone) so that the sequences are correct.
- Resetting your shutters
Perform this sequence 3 times :
Cut off general power 7 seconds
Restore power for 10 seconds
- Then turn off the power again for 7 seconds then leave the power on .
If everything goes correctly, all your shutters go down to the bottom stop. You then have 40 minutes maximum to carry out the rest of the operations.
- Activation of the new remote control
Make two short presses on the Up button (less than 0.5 seconds) - Resynchronize all remote controls in your installation, including any additional remote controls
To know :
This procedure is compatible with 2-button transmitters.
Replacement remote control: installation procedure for an autonomous or solar roller shutter
If you have a shutter equipped with a solar sensor, follow this part of our tutorial. Before you get started, take a moment to check the type of sensor that is on your box or wall.
Indeed, depending on the model, the shutter reset is slightly different.
⚠ Take all necessary precautions to avoid falling.
Initialization of a roller shutter equipped with an 11-cell sensor
To reset, you need to hide the sensor 4 times, with the following sequence:
_ Hide the sensor for 7 seconds
_ Leave natural light on for 10 seconds.
11 cells" src="https://lacentrale-eco.com/images/v5/articles_blog_lce/categorie_volant_roulant_fermeture_bonne_pratique/procedure-replacement-telecommande-11-cellules-initialisation.jpg?1680184889274" style="border-radius: 8px;" />
This reset step is successful if your shutter goes down completely. You can move on to the remote control activation phase.
Initialization of a roller shutter equipped with a 36-cell sensor
For these older versions, use the magnetic key provided with your shutter. It will be used for the reset phase.
Here is the action to carry out: if it is successful, your shutter goes down completely.
Now that your shutter is reset, you need to follow the steps outlined below. They must be done with less than 2 minutes between each one.
1. Activating the replacement remote
2 short presses on the Up button
2. Unlocking Transport mode
4 long presses on the Descent button . A press must be longer than 4 seconds
3. Learning the stops
1 short press on the descent for the lower stops and then 1 short press on the rise for the upper stop.
To confirm the stops, you must repeat this phase once.
4. Resynchronization of additional transmitters
Carry out this operation (2 short presses on the upstroke) using as many remote controls as possible. All within a maximum of 40 minutes after the start of shutter initialization.
Frequently Asked Questions
Conditions for replacing your remote control
Your shutter dates from before 2007
Bubendorff is unable to remanufacture your remote control. The solution: change the engine. It will come with a new remote control.
A good opportunity to take advantage of a more recent version, compatible with home automation solutions.
Your shutter was manufactured from 2007
Reproduction of your remote control is possible with the S/N number of your shutter.
This is reference 223019 . So, it will be produced specifically for you. So allow a delay of approximately 3 weeks.
Difference between a replacement remote control and a remote controladditional nde
A replacement remote control is intended to replace a lost or damaged one. It is designed to work with the same roller shutter as the original remote control and is programmed in the same way to ensure full compatibility.
For its part, an additional remote control will be used to control the same roller shutter as the original remote control. Depending on the version, it can be programmed to work with several roller shutters if necessary.
In summary, a replacement remote control is used to replace a lost or damaged original remote control, while an additional remote control is used to supplement the use of the original remote control.
discover our article: how to install an additional remote control?
the additional remote control in 2 button and 3 button version
