- Back to top
- Description
- Documentation
- Features
- Customer reviews
EUREKA MOB 95 watt drinking water treatment plate, domestic range
Treating the water with a UV lamp avoids the use of chemicals, and does not demineralise the water!
The set consists of:
1 UV reactor with CE marking
1 MCR type UV lamp and its connector.
1 40x4.5 EPDM gasket and 1 protected quartz sheath.
1 bag for fixing the electrical plate.
1 illustrated installation instructions
DescriptionEUREKA MOB 95
Allowable flow (40 mJ/cm² at 98% transmission) 4.22 m³/h
Treatment chamber
UV-C chamber volume 2.7 liters
Total weight packaged device 5.2 Kg
Inlet / Outlet 1'' no gas
Material 316L stainless steel
Operating pressure 4 bar
Max pressure 6 bar
Min / max water temperature 0 - 40°C
Electrical turntable
Weight < 1 Kg
Electrical power consumed 100 Wh
Protection Fuse 1 A
Supply voltage 220-230V AC –50Hz
Ambient temperature 0 - 30°C
UV-C lamp
Number of lamp 1
PLL 95W lamp reference
27W UV-C Germicidal Power
Lamp life 9000 hours
APPLICATION of UV treatment:
- Potabilization of raw water (boreholes, catchments, wells, etc.)
- Securing rainwater (sanitary use only)
- Securing mains water
PRINCIPLE of UV lamp treatment:
Purely physical potabilization process, associated with filtration destroying micro-organisms likely to cause illness or affect a manufacturing process.
This treatment is carried out by the germicidal effect of UVc rays, eliminating, among other microbes, viruses, bacteria and fungi, while respecting the environment.
Technical characteristics of EUREKA MOB UV boards:
- 316 L stainless steel treatment chamber
- Max pressure 6 bar
- Water temperature 0 to 40°C
- Manhole for control cell
- Connection in opposite axis
- Domed bottom quartz sheath
- Single-ended lamp 9,000 h
- electronic ballast
- Electrical box fixed on the chamber
- Green and red lamp status LEDs
- Daily counter with countdown of the number of days remaining and reset switch
- Lamp fault buzzer
- 220 V+E power cord
- 316L stainless steel mounting base
ADVANTAGES of this UV treatment system
- Optimization of the congestion/processed throughput ratio.
- Simplification during assembly or disassembly of the device due to:
- to the electrical box attached to the plate
- to the single-ended design of the germicidal lamp
- Reliability and safety of use:
- Meets the strictest sizing and design standards for complete disinfection of water intended for human consumption (according to the Ministerial Circular for Health of January 19, 1987).
- Low maintenance cost
- Without side effects
- Retained mineral salt content.
- No chemical residual product generated.
- Equipment declared to the Ministry of Health in accordance with the decree of August 21, 2008 for use in the treatment of rainwater.
- Optimized packaging
OPTIONS for EUREKA MOB UV treatment board model
- UVc control cell
- Wide range of possible mechanical filtration
- Possible power supply with photovoltaic panels
- Hydraulic safety solenoid valve in the event of a power cut or lamp fault
- Flow limiter to guarantee the UVc dose
Consumables and spare parts for EUREKA MOB Turntable
- UVc lamp: 9,000 hours
- Seal: 9,000 hours
- Sheath: 5 years
We work in close collaboration with the manufacturer to provide you with advice and validate your approach. We strongly invite you to get in touch with us, in order to check the feasibility of your project and the correct sizing of your installation.
- 3/4" ,
- 1"
- 2 year warranty. The electronics are guaranteed for 1 year.
- Eureka
No reviews found
You have a question ?